Phico D0 94v0 Lcd Display Datasheet Pdf |work| May 2026
These timings are easily met by any microcontroller, including Arduino at 16MHz. Since you need the PDF to program the display, here is the standard command set you will find inside the datasheet. Use these hex commands to control your PHICO D0.
This article serves as a complete, in-depth resource. We will dissect every part of that keyword—explaining what "PHICO" means, decoding the mysterious "D0", understanding the critical "94V-0" flammability rating, and finally, guiding you on how to find, read, and utilize the elusive datasheet PDF. phico d0 94v0 lcd display datasheet pdf
| Pin No. | Symbol | Level | Function | | :---: | :---: | :---: | :--- | | 1 | VSS | 0V | Ground | | 2 | VDD | +5V | Logic Power Supply | | 3 | V0 / VEE | Variable | Contrast Adjustment (via potentiometer to VSS) | | 4 | RS | H/L | Register Select: 0=Command, 1=Data | | 5 | R/W | H/L | Read/Write: 0=Write, 1=Read (often tied to GND) | | 6 | E | H→L | Enable signal (falling edge triggered) | | 7 | DB0 | H/L | Data Bus Bit 0 (LSB) – not used in 4-bit mode | | 8 | DB1 | H/L | Data Bus Bit 1 | | 9 | DB2 | H/L | Data Bus Bit 2 | | 10 | DB3 | H/L | Data Bus Bit 3 | | 11 | DB4 | H/L | Data Bus Bit 4 (MSB of low nibble in 4-bit mode) | | 12 | DB5 | H/L | Data Bus Bit 5 | | 13 | DB6 | H/L | Data Bus Bit 6 | | 14 | DB7 | H/L | Data Bus Bit 7 / Busy Flag | | 15 | LED_A | +5V | Backlight Anode (Power for backlight) | | 16 | LED_K | GND | Backlight Cathode (Ground for backlight) | These timings are easily met by any microcontroller,
| Parameter | Typical Value for PHICO D0 Series | | :--- | :--- | | | 16 Characters x 2 Lines (16x2) | | Display Type | STN (Super Twisted Nematic) or FSTN | | Polarizer Mode | Transflective (readable in sun & via backlight) | | Viewing Direction | 6 o'clock (or 12 o'clock – check datasheet) | | Backlight | Yellow-Green or White LED (parallel or series) | | Controller | KS0066 or S6A0069 (HD44780 compatible) | | Interface | 4-bit or 8-bit parallel (14+2 pins) | | Operating Voltage | 4.5V to 5.5V (typically 5.0V) | | Logic Supply Current | 1.0 mA (typical without backlight) | | Backlight Current | 120-200 mA (depends on color) | | Duty Cycle | 1/16 duty, 1/5 bias | | Operating Temp | 0°C to +50°C (Standard) / -20°C to +70°C (Extended, if specified) | Part 3: The Essential Pinout (Without the Datasheet) Most PHICO 94V-0 displays use the standard 16-pin header configuration (0.1-inch pitch). Here is the pinout you will likely find in the datasheet PDF: This article serves as a complete, in-depth resource
Introduction In the world of embedded systems, consumer electronics, and industrial control panels, few components are as ubiquitous yet as technically nuanced as the alphanumeric LCD display. For engineers and hobbyists searching for the term "phico d0 94v0 lcd display datasheet pdf" , you are likely holding a 16x2 or 20x4 character LCD, trying to reverse-engineer a product, or seeking a reliable replacement.